Vol. 7 (04) pp. 118-133 DOI: 10.21474/IJAR01/8799

EFFECT OF INJECTION TIMING AND NOZZLE HOLE GEOMETRY ON COMPRESSION IGNITION ENGINE FUELLED WITH THEVETIA PERUVIANA BIODIESEL.

and
  • Research Student, Sri SatyaSai University of Technology and Medical Sciences, Sehore, Madhya Pradesh 466001.
  • Research Guide,Sri SatyaSai University of Technology and Medical Sciences, Sehore, Madhya Pradesh 466001.
18 Downloads 91 Views
Crossref

Download Full Paper (PDF)

Abstract

In the present study an experimental work had been carried out to analyze the performance and emission characteristics of various blends of thevetiaperuviana biodiesel by varying injection timings and nozzle hole geometry. The engine tests are conducted on Kirloskar, 4-stroke, single cylinder, 1500 rpm, water cooled, direct injection, diesel engine with Eddy Current Dynamometer with standard injection pressure 230 bar and injection timing 23?BTDC was maintained constant throughout the experiment. Three different injection timings such as 20?BTDC, 23?BTDC and 26?BTDC and three different nozzles such as 3 hole, 4 hole and 5 hole are varied to analyze the performance and emission characteristics. From the test results, it could be observed that among three different injection timings 26?BTDC and among three different nozzles 5 hole nozzle gives higher efficiency and lower emissions as compared to other two injection timings and other two nozzles.

Keywords

Article Analytics

References

  1. R.Pradeep, K.Annamalai, S.R.Prem, ?Influence of Injection Timing on Emission Parameters of Adelfa Biodiesel (Nerium Oil Methyl Ester ? NOME) Fuelled DI CI Engine?, International Journal of Innovative Technology and Research, 2013, 1(1), 99-102.
  2. Prabhakar, V.N.Banugopan, K.Annamalai, S.Jayaraj, ?Optimization of Esters of Nerium Biodiesel in a Diesel Engine?, Indian Journal of Science and Technology, 2011, 4(3), 170-172.
  3. Suresh, G.Naidu, A.Venkata, ?Performance and Emission Evaluation of a DI Diesel Engine Using Nerium Oil as Alternative Fuel?, International Journal of Engineering Research and Technology, 2013, 2(9), 2510-2517.
  4. J.Lalvani, M.Parthasarathy, D.Balasubramaninan, K.Annamalai, ?Experimental Investigation on DI Diesel Engine with Renewable Biodiesel ? Adelfa?, National Conference on Green Engineering and Technologies for Sustainable Future 2014, Journal of Chemical and Pharmaceutical Sciences, 2014, Special Issue-4, 240-242.
  5. B.John, M.Subramanian, ?Study of Performance, Emission and Combustion Parameters of a Direct Injection Diesel Engine using Eucalyptus and Nerium Biodiesels as fuel?, International Journal of Science, Engineering and Technology Research, 2014, 3(4), 692-698.
  6. Tyagi, A.Sharma, ?Experimental Investigation of Neem Methyl Esters as Biodiesel on CI Engine?, International Journal of Engineering and Applications, 2012, 2(4), 1673-1679.
  7. Deokar, Harari, Sutar, Hodage, Patil, Kole, ?Effect of Nozzle Hole Geometry on Compression Ignition Engine Fuelled with ThevetiaPeruviana Biodiesel?, International Journal of Innovative Research in Science, Engineering and Technology (IJIRSET), 2018, 7(12), 11861-11871.
  8. Chavan, Sutar, Bhatkande, Gurav, Mulla, Deokar, Harari, ?Experimental Studies on Production of Biodiesel from ThevetiaPeruviana Feedstock?, International Journal of Engineering and Management Research (IJEMR), 2018, 8(2), 46-49.
  9. Harari, ?Experimental Investigation on the Performance and Emission Characteristics of Compression Ignition Engine Fuelled with Various Blends of Water Melon Biodiesel?, Integrated Research Advances (IRA), 2017, 4(1), 18-23.
  10. Harari, Ghadge, ?Experimental Investigation on the Performance Characteristics of Compression Ignition Engine Fuelled with Various Blends of CalophyllumInophyllum Biodiesel?, International Research Journal of Engineering and Technology (IRJET), 2016, 3(8), 752-757.
  11. Sayin, M.Gumus, M.Canakci, ?Influence of injector hole number on the performance and emissions of a DI diesel engine fueled with biodiesel-diesel fuel blends?, Applied Thermal Engineering 61 (2013) 121-128.
  12. Sharma, R.R.Singh, S.K.Vishwakarma, ?Experimental study of the effect of fuel injector nozzle holes on direct injection diesel engine?, IOSR Journal of Mechanical and Civil Engineering, Volume-7, Issue-4, Pages 67-74, 2013.
  13. P.Varghese, R.Saxena, R.R.Lal, ?Analysis of the effect of nozzle hole diameter on CI engine performance using karanja oil-diesel blends?, International Journal of Mechanical Engineering and Technology, Volume-4, Issue-4, Pages 79-88, 2013.
  14. S.Kumar, ?Experimental investigation of injectors nozzle hole on CI engine using jatropha oil as biofuel?, International Journal of Scientific Research Engineering & Technology, Volume-3, Issue-8, Pages 1209-1215, 2014.
  15. L.Swamy, T.K.Chandrashekar, N.R.Banapurmath, P.Nashipudi, ?Effect of injection timing, combustion chamber shapes and nozzle geometry on the diesel engine performance?, Universal Journal of Petroleum Sciences 2 (2014), 74-95.
  16. V.Khandal, N.R.Banapurmath, V.N.Gaitonde, R.S.Hosmath, ?Effect of number of injector nozzle holes on the performance, emission and combustion characteristics of honge oil biodiesel (HOME) operated DI compression ignition engine?, Journal of Petroleum and Environmental Biotechnology 2015, 6:3.
  17. A.Harari, D.S.Akshatha, G.Manavendra, ?Effect of Injection Pressure and Nozzle Hole Diameter on Combustion Parameters of CI Engine Fuelled with B20 Neem Blend?, International Journal of Innovative Research in Science, Engineering and Technology, 2015, 4(5), 2857-2870.
  18. A.Harari, G.Manavendra, ?Experimental Investigation on the Combustion Parameters of B20 Neem Blend in CI Engine by Varying Injection Timing and Nozzle Hole Diameter?, International Journal of Advanced Research and Innovative Ideas in Education, 2015, 1(4), 503-510.
  19. A.Harari, J.S.Patil, ?A Review on Effect of Nozzle Hole Geometry on the Performance, Combustion and Emission Parameters of CI Engine Fuelled with Diesel and Biodiesel?, International Journal of Engineering and Management Research, 2016, 6(3), 39-48.
  20. A.Harari, D.S.Akshatha, G.Manavendra, ?Influence of Injection Pressure and Nozzle Hole Diameter on Performance of CI Engine Fuelled with B20 Neem Blend?, National Conference on Trends and Innovations in Automation, Materials and Thermal Engineering held on 21 & 22 May 2015 at Visvesvaraya Technological University, Mysuru.

How to Cite This Article

A.J. Deokar and G.R. Selokar. (2019); EFFECT OF INJECTION TIMING AND NOZZLE HOLE GEOMETRY ON COMPRESSION IGNITION ENGINE FUELLED WITH THEVETIA PERUVIANA BIODIESEL., Int. J. of Adv. Res., 7 (04), 118-133, ISSN 2320-5407. DOI: https://doi.org/10.21474/IJAR01/8799

Corresponding Author

A.J. Deokar
Research Student, Sri Satya Sai University of Technology and Medical Sciences, Sehore, Madhya Pradesh 466001
Creative Commons Attribution 4.0 This work is licensed under a Creative Commons Attribution 4.0 International License.